Accessories
-
R Polycarbonate Profile - 16mm
FROM $3.03 L/ftR Polycarbonate Profile - 16mm
FROM $3.03 L/ftThe R profile is specifically designed for sealing polycarbonate sheet edge on corners. It can be applied even after the solid/vented aluminum tape, it can easily allow you to make corners with 2 polycarbonate sheets. It also cover hollow sheets edge to prevent dust, water and bug get access to the hollow space by providing a neat finish.
It can be easily cut.
-
PoliLock System® - H Aluminum Structure 16-35mm
FROM $6.78 L/ftPoliLock System® - H Aluminum Structure 16-35mm
FROM $6.78 L/ftIt is specially designed to be screwed to the frame for connecting 2 sheets on the length side. It can be used for polycarbonate sheets and acrylic sheets from 16 to 35mm.
- Easy assembly and installation •High quality, long lasting, and weather resistant aluminum extrusion
- Distributes load pressure to prevent stress on sheets
- Cap is fixed to the base holding sheets firmly in place
- High quality gaskets prevent the penetration of water, dust, and dirt
- Seamless finish with concealed screw covers
-
H Polycarbonate Profile - 16mm
FROM $1.93 L/ftH Polycarbonate Profile - 16mm
FROM $1.93 L/ftThe H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut
It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.
-
F Polycarbonate Profile - 16mm
FROM $2.70 L/ftF Polycarbonate Profile - 16mm
FROM $2.70 L/ftThe F profile is special designed for sealing polycarbonate sheet edge. Applied after the solid aluminum tape, it can covers polycarbonate hollow sheet edge to prevent dust, water and bug get access to the hollow space. It provides a neat finish to the cut sheet edge.
It is used at the edge of polycarbonate sheets, where sheets are being fixed to side of building, rafter or other substrate.It can be easily cut.
-
U Polycarbonate Profile - 16mm
FROM $1.10 L/ftU Polycarbonate Profile - 16mm
FROM $1.10 L/ftThe U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut
The profile can be easily cut
In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.
-
U Polycarbonate Profile - 25mm
FROM $1.60 L/ftU Polycarbonate Profile - 25mm
FROM $1.60 L/ftThe U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut
The profile can be easily cut
In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.
-
U Aluminum Profile - 16mm
FROM $1.70 L/ftU Aluminum Profile - 16mm
FROM $1.70 L/ftThe U Aluminum profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut
The profile can be easily cut
In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.
-
Solid Aluminum Tape
As low as FROM $11.43Solid Aluminum Tape
As low as FROM $11.43The solid tape should be applied on the top width edge of the polycarbonate sheets to prevent water, dust and dirt to get inside the ribs. Different sizes available for panels from 4 to 45mm.
-
Vented Aluminum Tape
As low as FROM $30.93Vented Aluminum Tape
As low as FROM $30.93The solid Vented tape should be applied on the bottom width edge of the polycarbonate sheets to allow condensation drainage and prevent dust and dirt to get inside the ribs. Different sizes available for panels from 4 to 45mm.