Accessories

Showing 19-29 of 29 results

per page
Set Descending Direction
  1. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  2. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  3. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  4. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  5. The F profile is special designed for sealing polycarbonate sheet edge. Applied after the solid aluminum tape, it can covers polycarbonate hollow sheet edge to prevent dust, water and bug get access to the hollow space. It provides a neat finish to the cut sheet edge.

    It is used at the edge of polycarbonate sheets, where sheets are being fixed to side of building, rafter or other substrate.

    It can be easily cut.

  6. Out of stock
    F Polycarbonate Profile - 8-10mm F Polycarbonate Profile - 8-10mm

    The F profile is special designed for sealing polycarbonate sheet edge. Applied after the solid aluminum tape, it can covers polycarbonate hollow sheet edge to prevent dust, water and bug get access to the hollow space. It provides a neat finish to the cut sheet edge.

    It is used at the edge of polycarbonate sheets, where sheets are being fixed to side of building, rafter or other substrate.

    It can be easily cut.

  7. The H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut

    It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.

  8. The H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut

    It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.

  9. The H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut

    It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.

  10. It is specially designed to be screwed to the frame for connecting 2 sheets on the length side. It can be used for polycarbonate sheets and acrylic sheets from 16 to 35mm.

    • Easy assembly and installation •High quality, long lasting, and weather resistant aluminum extrusion
    • Distributes load pressure to prevent stress on sheets
    • Cap is fixed to the base holding sheets firmly in place
    • High quality gaskets prevent the penetration of water, dust, and dirt
    • Seamless finish with concealed screw covers
  11. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

Showing 19-29 of 29 results

per page
Set Descending Direction