Accessories

14 Items results

per page
Set Descending Direction
  1. Ideal for polycarbonate sheets of small thickness. It is used for connecting 2 sheets side by side through a base and cape polycarbonate elements. 

  2. It is specially designed to be screwed to the frame for connecting 2 sheets on the length side. It can be used for polycarbonate sheets and acrylic sheets from 4 to 12mm.

    • Easy assembly and installation •High quality, long lasting, and weather resistant aluminum extrusion
    • Distributes load pressure to prevent stress on sheets
    • Cap is fixed to the base holding sheets firmly in place
    • High quality gaskets prevent the penetration of water, dust, and dirt
    • Seamless finish with concealed screw covers
  3. The H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut

    It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.

  4. It is specially designed to be screwed to the frame for connecting 2 sheets on the length side. It can be used for polycarbonate sheets and acrylic sheets from 16 to 35mm.

    • Easy assembly and installation •High quality, long lasting, and weather resistant aluminum extrusion
    • Distributes load pressure to prevent stress on sheets
    • Cap is fixed to the base holding sheets firmly in place
    • High quality gaskets prevent the penetration of water, dust, and dirt
    • Seamless finish with concealed screw covers
  5. The H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut

    It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.

  6. The H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut

    It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.

  7. The H profile is special designed for connecting two polycarbonate sheets together on their length side. It must not be screwed, just applied to the two panels. It can be easily cut

    It should be applied on the length side of the panel, as shown in pictures. The Polycarbonate H profile is very easy to cut.

  8. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  9. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  10. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  11. The U Polycarbonate profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  12. The U Aluminum profile is designed to seal the edge of the polycarbonate sheets. Applied after the solid/vented aluminum tape it close the edge to prevent dust, water and bug get access to the hollow space. It also provide a a clear finish to the edge of the sheet. It can be easily cut

    The profile can be easily cut

    In order to prevent dust and dirt penetrating inside the ribs, the exposed top and bottom ends (the width side of a sheet) must always be sealed first with the solid aluminum tape on the top and vent tape at the bottom.

  13. Solid Aluminum Tape

    As low as FROM $11.43
    Solid Aluminum Tape
    As low as FROM $11.43

    The solid tape should be applied on the top width edge of the polycarbonate sheets to prevent water, dust and dirt to get inside the ribs. Different sizes available for panels from 4 to 45mm.

  14. Vented Aluminum Tape

    As low as FROM $30.93
    Vented Aluminum Tape
    As low as FROM $30.93

    The solid Vented tape should be applied on the bottom width edge of the polycarbonate sheets to allow condensation drainage and prevent dust and dirt to get inside the ribs. Different sizes available for panels from 4 to 45mm.

14 Items results

per page
Set Descending Direction